|
|
 |
|
|
Cable Shifters For Single and Dual Transfer Cases 
As our sport progresses, so do our drivetrains. With the latest dual transfer case kits, extreme clocking rotations, and non-stock combinations we felt the need for a far more flexible system than what linkage type shifters could provide. Typically a transfer case shifter linkage consists of a fixed pivot point on the transfer case or adaptor, with connecting rods between the transfer case shift rails and shifters in the cab. For the few with stock transmission and transfer case combinations they work fine, but for many, especially those with modified drivetrains, they leave something to be desired. When body lifts are added, transfer cases are clocked, or a dual transfer case kit is added, stock linkages are no longer adequate. For these reasons and more, we have developed our line of Transfer Case Cable Shifters.  Cable shifters are the most versatile shifters you can get for your transfer case. Since the cables mount directly to the transfer case, they rotate with the case when it is clocked up or down. No more need to worry about linkage bind with extreme clocked cases. 
The Cable Shifter Box is independant of the transfer case, coupled via the cables. This allows the user to mount the shifter box wherever required, on the floor, in a console, or even on the dash. When mounted flush, the cables exit below the mounting surface undetected. Included in the kit are self tapping sheet metal screws for mounting the base and trim ring. 
We use some of the toughest, high quality push/pull cables availible. Rated to 230/350lbs of input force, and temperature rated from -65F to 230F degrees, these are designed to handle the toughest conditions. The cables are pre-permanintly lubricated, sealed with a floating wiper seal. 
Our Cable Shifter Kits include everything you need for both the transfer case, and cab of the truck for installation. We provide 3 foot cable lengths with the kits. All fasteners are mechanical locking, to assure tension after installation. Our shifter kits are low profile, and usually require very little floorboard modifications to fit. We ship our shifter kits primer black for corrosion resistance. ______________________________________________________________________ 
We are now offering cable shifter kits for the D300 transfer case. Mechanical Shifters won't fit? We have the solution for you. Our cable shifter kits include all the hardware, control cables (3' Standard), shifter boots and laser cut bracketry. ______________________________________________________________________ 
In some applications our standard Dana 300 Cable Shifter kit just won't fit. This can be the case a when using large manual transmission mated to your D300 or especially in a 'flipped' drivers side drop application of the D300. We solved this problem with our Dana 300 'Reverse' Shifter Kit. 
The Dana 300 Reverse Cable Kit Routes the cables from the rear of the transfer case and above (in standard passenger side drop, shown above), or below (in flipped drivers side drop, shown right) to clear the front driveshaft. Standard cable length is 4' as the extra length is needed to make the loop to the rear. You are required to cut off the factory cast shifter mount on the Dana 300 front output retainer for installation. ______________________________________________________________________ We are the exclusive supplier of Cable Shifters for your STak Transfer Case STaK 2 Speed Monster Box, Mini Monster Box and 2 Speed BBox - $279.00 STaK 3 Speed Monster Box, Mini Monster Box and 3 Speed BBox - $349.00 STaK D300 Replace - A - Case $279.00 Atlas II Cable Shifter Kit - $279.00 Atlas 4 speed - CALL. ______________________________________________________________________ 
We offer cable shifter kits for both drivers and passenger side drop NP205's, both divorced and married type. Our cable shifter kits include all the hardware, control cables (3' Standard), shifter boots and laser cut bracketry. These dual cable kits are designed for a transfer case that has had the rails modified for twin stick application. ______________________________________________________________________ 
This kit provides shifters to shift the NP203 range box and NP205 transfer case. This kit is designed for modified NP205's that use one shifter to shift high and low range and one shifter to shift front wheel drive, rear wheel drive or 4wd. We can provide shifters for any rotation and combination of NP203/NP205's. This kit will also work with many other dual transfer case brands. ______________________________________________________________________ |
|
 |
NorthWest FabWorks
1-250-248-6024
All content © 2004 - 2005 by NorthWest FabWorks